brickrennes       19/10/2009 07:56

Host: No mostrado/ Not shown    IP: No mostrado/ Not shown    Sistema: Windows XP

Re: XbusTCO and NanoX-S88

Publicidad hi; the night have send me other ideas for your problem..... what is your turnout interface? commercial or "Paco"? if Paco, what it use à supplementy power on the module? is possible to the power is too low for tranferring the data informations to the turnout decoder. verify what, an other accessory on your xpress net have not an identical adress xpress net if you have a shortly flash on the led 1 ; your system appear fonctionnal ; its a problem of transmission on the signal, or wiring connexion (your diodes on the xbus tco are on the good way?) . test to reprogramming your pic.....verify alls connexions..... i have one problem, with turnout system with tco ; when, on the nanox ask modifiy the CV 7 to use with "lenz like system" ; the turnout are not fonctionnaly ; i have keeping the "lokmaus system" , on the programming CV7 configuration ; its possible to your nanox has a wrong programmation about CV7...after modification, i have no problem with nano x and turnout system, and command via xbus tco (information about, on the pdf "nanoxs88". best regards Brickrennes >Hallo! > >>HI christoph ; >> >>the xbus tco is compatible with nanoxs88 ; verify your xpressnet adress on the dip switch, and is the number 6 dip is "on" (use with "lenz" mode ; the mode used with nanoxs88 > >My XpressNET address is set to 31 and the dip 6 is set to on. >> >>on normal run, all led are off ; on your situation, what is the status of your leds? "light" of "flash", >> >The Status of all leds is off until i switch a turnout to or or back to off, then LED1 is going to flash shortly. > >>what system use you? for your tco? inter or 2 buttons by turnout? ; verify your program "hex" writting on your pic ; i dont think is the raison of non functionment. >> >I'm using the switch version, and as you can see, the TCO does work, if switched to address 5 on a lockmaus, but does not work on the NanoX neither on Address 5 nor aon address 31. > >>i leave other persons on this forum for indicating other possibility.... >> >>Best regards >> >>Brickrennes >> >> >> >> >>>Hello! >>> >>>Is it possible to run the XbusTCO with a NanoX-S88? >>>It seems not to work, I've tried it with a Lokmaus >>>and it runs perfect, but with a XbusTCO it does nothing. >>> >>>Is the XbusTCO designed to work also with the NanoX? >>> >>>Thank you for your Answer. >>>Christoph

Respuestas (1)

XbusTCO and NanoX-S88 - Christoph - 18/10/2009 16:06  Re: XbusTCO and NanoX-S88 - brickrennes - 18/10/2009 22:19  Re: XbusTCO and NanoX-S88 - Christoph - 19/10/2009 00:06  » Re: XbusTCO and NanoX-S88 « - brickrennes - 19/10/2009 07:56  Re: XbusTCO and NanoX-S88 - fmco ® - 26/10/2009 21:46

Responder

Nombre E-Mail Asunto Web Enlace a una imagen Notificar por e-mail respuestas. Mensaje >hi; > >the night have send me other ideas for your problem..... > >what is your turnout interface? commercial or "Paco"? if Paco, what it use à supplementy power on the module? is possible to the power is too low for tranferring the data informations to the turnout decoder. > >verify what, an other accessory on your xpress net have not an identical adress xpress net > >if you have a shortly flash on the led 1 ; your system appear fonctionnal ; its a problem of transmission on the signal, or wiring connexion (your diodes on the xbus tco are on the good way?) . > >test to reprogramming your pic.....verify alls connexions..... > >i have one problem, with turnout system with tco ; when, on the nanox ask modifiy the CV 7 to use with "lenz like system" ; the turnout are not fonctionnaly ; i have keeping the "lokmaus system" , on the programming CV7 configuration ; its possible to your nanox has a wrong programmation about CV7...after modification, i have no problem with nano x and turnout system, and command via xbus tco (information about, on the pdf "nanoxs88". > > >best regards > >Brickrennes > > > >>Hallo! >> >>>HI christoph ; >>> >>>the xbus tco is compatible with nanoxs88 ; verify your xpressnet adress on the dip switch, and is the number 6 dip is "on" (use with "lenz" mode ; the mode used with nanoxs88 >> >>My XpressNET address is set to 31 and the dip 6 is set to on. >>> >>>on normal run, all led are off ; on your situation, what is the status of your leds? "light" of "flash", >>> >>The Status of all leds is off until i switch a turnout to or or back to off, then LED1 is going to flash shortly. >> >>>what system use you? for your tco? inter or 2 buttons by turnout? ; verify your program "hex" writting on your pic ; i dont think is the raison of non functionment. >>> >>I'm using the switch version, and as you can see, the TCO does work, if switched to address 5 on a lockmaus, but does not work on the NanoX neither on Address 5 nor aon address 31. >> >>>i leave other persons on this forum for indicating other possibility.... >>> >>>Best regards >>> >>>Brickrennes >>> >>> >>> >>> >>>>Hello! >>>> >>>>Is it possible to run the XbusTCO with a NanoX-S88? >>>>It seems not to work, I've tried it with a Lokmaus >>>>and it runs perfect, but with a XbusTCO it does nothing. >>>> >>>>Is the XbusTCO designed to work also with the NanoX? >>>> >>>>Thank you for your Answer. >>>>Christoph      Ver mi mensaje despues de insertarlo.