Free 256Ch. DMX512 Interface
|
Connected from 38.107.191.104 ( 38.107.191.104 ) Active sessions on this forum 1 Active sessions on all forums 4305 |
|
|
MANOLATOR
Free 256Ch. DMX512 Interface |
|
||
|
||||
|
|
| Topic | Data |
|
Enttec "open failed" Hola buenas! Vereis, acabo de recibir mi nuevo interfce enttec, pero al conectarlo al portatil me pide drivers y no tengo ni idea de cuales tengo que instalar, he puesto unos de Ftdi que se suponen lo convierten en un puerto COM, pero me parece que ... |
|
chema
04/22/2005 15:29 |
|
Found Your Site only in Archives Hi there, I've found your site by a link in the Freestyler Page. When there was no response from the hoster I opened it by the webarchive http://web.archive.org/web/20041012123241/http://webs.ono.com/usr044/MegaTech/index.htm but they don't ... |
|
Joe
04/19/2005 16:06 |
|
New MaxiSpam alpha to download Hello: New MaxiSpam alpha to download in the More! section. It can do only manual operations with the manolator256 interface yet, but it has skin support... Thanks to try and to send me th bugs... Cheers Manuel |
|
Manuel Martin
04/03/2005 18:53 |
|
Schematic question I am looking at the schematic for the no Xtal version, as well as Kristof's original. The capacitor shown has the unit listed as: nF Is this microfarad? (normally shown with the funky letter u) What type of capacitor should it be? electroly ... |
|
Steve
03/22/2005 00:37 |
|
DMX Protocol I going to create my own Converter (USB to DMX) and searched for the correct protocol! May you can send me the timing and the protocol details, like what are the timings, start and stop bits/bytes, databytes (adressbytes?) I hope for reply Chri ... |
|
Christian
02/27/2005 17:12 |
|
I think my site is alive again... Thanks to all! |
|
Manuel Martin
02/14/2005 22:24 |
|
My site have been closed... Hello: My site have been closed by my web internet provider. I have been forced to buy some space at the web... an I hope next week I will upload the site to this new web place. It is a shame but I must spend more money to share interenting free t ... |
|
Manuel Martin
02/13/2005 21:43 |
|
The site is deactivate The site is deactivate. anyone can give me the schemantic circuit? thank mix |
|
Mix
02/12/2005 11:26 |
|
SN75176 Hello! I will built the Manolator too. Is the SN 75176 the same as the SN 75176BP? Can I use it? Thanks! Sascha |
|
Sascha
02/07/2005 19:17 |
|
Help - Only works using test software iv build the board up and plugged into my Omega 2 scanning head (5 channel) iv tried it in loads of software but all it does is go nuts the only software it works in is (Testit "MANOLATOR") with the following settings data present - 50 DM ... |
|
Russell
02/07/2005 02:24 |
|
Interface not working I built the interface but its not working with my Martin MiniMac Profiles. I was wondering if it might be with the Pic programming. What should the fuse settings be set at? |
|
James Tompkins
02/06/2005 10:33 |
|
Please, tell me if all your problems have been fixed or not! Hello all: Sometimes some of you asked me for help, but after my answer you dont email me to know if the problem have been fixed... Please let me know how it ends. Cheers Manuel Martin. |
|
Manuel Martin
02/02/2005 19:08 |
|
Win 95 Hello, How do I get the proggi running under Win95 on a PC 486 8 MB Best regards |
|
Jan Steensels
01/30/2005 22:08 |
|
Manolator - Please HELP ME!! Hi, I have built the Manolator, it will not work with Freestyler or the Manoltor software, it will work with DMXContol though. We I use it with the Manolator software it doesn't work, I will blackout though!. I am using the No Crystal version ... |
|
Claire
12/30/2004 00:06 |
|
PIC Programmer Help Hello, I have built the Pic programmer and it isn't working. Can someone please tell me what voltage the MCLR pin is supposed to go from and to. Mine goes from 11.48V to 13.2V when initialised in the check hardware menu. The red LED is always o ... |
|
Jason
12/28/2004 14:43 |
|
Manolator256 ASM files Manolator256 Interface Pic 16F88 Source code Free to download, to open with MPLAB: http://webs.ono.com/usr013/MasterPeace/files/Manolator_ASM.zip http://webs.ono.com/usr013/MasterPeace/files/Manolator_ASM_noXtal.zip |
|
Manuel Martin
12/26/2004 18:19 |
|
Oshon PIC programmer - Help Please !! Hi, I have just built the Manolator, to program the PIC (PIC16F88)I built the Oshon Programmer. The programmer isn't programming the chip. It says it has then when I verify it it says: - verify failed at address 000h! The read value from that a ... |
|
jason
12/24/2004 23:25 |
|
VBasic Manolator Software Source free to download !! Hello: This is the link to download the source of the last beta of Manolator software http://webs.ono.com/usr013/MasterPeace/files/ManolatorSource.zip Also MasterPeace versions have been updated. Enjoy. Manuel Martin |
|
Manuel Martin
12/17/2004 23:20 |
|
ASM Hola. Queria saber si me podian pasar el ASM del PIC ya que me gustaria compilarlo y probarlo con un micro mas grande para agregarle otras funciones. Manuel me interesaria saber si es posible modificar el programa para que acepte un teclado que cone ... |
|
Matias Fernando
12/10/2004 20:40 |
|
ASM Hola. Queria saber si me podian pasar el ASM del PIC ya que me gustaria compilarlo y probarlo con un micro mas grande para agregarle otras funciones. Manuel me interesaria saber si es posible modificar el programa para que acepte un teclado que cone ... |
|
Matias Fernando
12/10/2004 20:29 |
| «« Messages 81 - 100 of 162 - 1 2 3 4 5 6 ... - « » |
| Post new topic |  |
| [Back] | |